Quested
Technical information
Description
A compact self-powered active speaker with full magnetic shielding. Ideal for a wide variety of applications including installations, workstation monitor, nearfield, surround sounds, and many more.
Size (WxHxD) 225mm x 316mm x 295mm (9" x 12.5" x 11.5") Weight 12.5 kgs (27.5 lbs) Drivers Bass cone 165 mm(6.5 in) High Frequency softdome 28mm (1.12 in) Maximum SPL >100db continues music material at 1m Frequency Response 65Hz - 20KHz +/- 3dB Input Connector XLR 3 Type Female and 1/4" RTS jack. Either can be used as link. Impedance 10 ohm. Electronically balanced RFI filtered Wiring Pin 1 ground or Sleeve, Pin 2 hot or Tip, Pin 3 cold or Ring Gain control +/-10dB Continuous control Filters Subsonic -3dB at 50Hz, 12dB/oct. Ultrasonic -3dB at 110kHz, 6dB/oct. HF Contour 2 three-position switches, offering 3 lift and 3 cut settings (see frequency plot for effect of settings). LF Contour 2 three-position switches, offering 3 lift and 3 cut settings (see frequency plot for effect of settings). Crossover 1.5kHz Power Amplifer LF output power 110W rms HF output power 40W rms T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz typ. 0.005% at 20W rms 1kHz. Hum + Noise >-100dB referred to clip Indication Power on Front mounted LED (green) indicates power applied Thermal protection Fully protected Power requirements Voltage Set by internal plug: normal 115V or 230V at 50 - 60Hz AC. F11A Frequency response and contour selection F11A Frequency response on axis & 30 degrees off axis | Technical information
Size (WxHxD) 435mm x 500mm x 600mm (17" x 19"n x 23") Weight 36 kgs (79 lbs) Drivers Bass: 300 mm (12 in) Maximum SPL LCR 100dB(C) Effects 103dB(C) Inputs Connectors 4 off XLR Female: Left, Centre, Right, Effects Impedance 10 kohm. Electronically balanced RFI filtered Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Outputs Connectors 4 off XLR Male: Sub, Left, Centre, Right Impedance > 100 ohm electronically balanced Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Full Range Channels L,C,R input to output High Pass: 38HZ at 12dB/oct. Passband gain: 0dB Sub Woofer Channel Signal Path All inputs are passband filtered and summed to Sub output and Sub amplifier. L,C,R input to Sub High pass: 15Hz at 18dB.oct. Low pass: 38Hz at 12dB.oct. Effects input to Sub High pass: 15Hz at 18dB.oct. Low pass: 100Hz at 24dB.oct. Effects level trim +/- 10dB Sensitivity switch +4dBu for nominal level: clip > +16dBu input at 22 Hz or -10dBu for nominal level: clip > +2dBu input at 22 Hz Level Trim Rear rotary preset +/- 10dB Signal Polarity Rear switch to invert sub channel polarity Phase Correction: Rear rotary preset to adjust 10-170 degrees at 38 Hz Power Amplifer Sub output power >400W rms into 8 ohm continuous.* T.H.D. <0.03% at levels up to 1dB below clip, 10Hz - 100Hz typ. 0.005% at 20W rms 20Hz. Hum + Noise >-105dB referred to clip Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (red) indicates 0.5dB below signal clip. Thermal protection Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C. Power requirements Voltage Set by internal plug: nominal 115V or 230V at 50 - 60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiscent: 45W. Typical use: 150W. Max: 580W. *Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperature <30 C. | Technical information
Size (WxHxD) 685mm x 550mm x 695mm (27" x 21.75" x 27.5") Weight 62 kgs (137 lbs) Drivers Bass: 380 mm (15 in) Maximum SPL LCR 110dB(C) Effects 113dB(C) Inputs Connectors: 4 off XLR Female: Left, Centre, Righ, Effects Impedance: 10 kohm. Electronically balanced RFI filtered Wiring: Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Outputs Connectors: 4 off XLR Male: Sub, Left, Centre, Right Impedance: > 100 ohm electronically balanced Wiring: Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Full Range Channels L,C,R input to output High Pass: 38HZ at 12dB/oct. Passband gain: 0dB Sub Woofer Channel Signal Path: All inputs are passband filtered and summed to Sub output and Sub amplifier. L,C,R input to Sub: High pass: 15Hz at 18dB.oct. Low pass: 38Hz at 12dB.oct. Effects input to Sub: High pass: 15Hz at 18dB.oct. Low pass: 100Hz at 12dB.oct. Effects level trim: +/- 10dB Sensitivity switch: +4dBu for nominal level: clip > +16dBu input at 22 Hz or -10dBu for nominal level: clip > +2dBu input at 22 Hz Level Trim: Rear rotary preset +/- 10dB Signal Polarity: Rear switch to invert sub channel polarity Phase Correction: Rear rotary preset to adjust 10-170 degrees at 38 Hz Power Amplifer Sub output power >400W rms into 8 ohm continuous.* T.H.D. <0.03% at levels up to 1dB below clip, 10Hz - 100Hz typ. 0.005% at 20W rms 20Hz. Hum + Noise >-105dB referred to clip Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (red) indicates 0.5dB below signal clip. Thermal protection Front mounted LEF turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C. Power requirements Voltage Set by internal plug: nominal 115V or 230V at 50 - 60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiscent: 45W. Typical use: 150W. Max: 580W. *Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperature <30 C. |
Technical information
Size (WxHxD) 340mm x 405mm x 340mm (13.5" x 16" x 13.5") Weight 22 kgs (48.5 lbs) Drivers Bass: 200 mm (8 in) HF: soft dome 28mm (1.125in) Maximum SPL LCR 108dB(C) Frequency Response 55Hz - 18kHz +/-2dB Input Connector: XLR3 Female Impedance: 10 kohm. Electronically balanced RF filtered Wiring: Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Sensitivity: Rear switch to select: -18dBu to 0dBu in 2dB steps for 100dB SPL Max input for clip +20dBu at 5kHz on 0dBu setting Filters Subsonic: -3dB at 27Hz, 12dB/oct (LF equaliser out). RF: -3dB at 250Hz, 6dB/oct (HF equaliser out). Crossover: 1.25kHz, 24dB/oct. User LF EQ: 3 position rear switch to select OFF for normal use (nominally flat), EXTENDED for nominal +1dB lift below 55 Hz, and OUT for use with an external sub-woofer. User HF EQ: 3 position rear switch to select OFF for normal use (nominally flat), LIFT for nominal +1dB from 5kHz and CUT -1dB from 6kHz. Power Amplifer LF output power: >110W rms continuous.* HF output power: >100W rms continuous.* * The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperature is < 30°C. T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz typ. 0.005% at 20W rms 1kHz. Hum + Noise >-100dB referred to clip Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (flashes red) indicates 0.5dB below signal clip. Thermal protection Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20°C. Power requirements Voltage Set by internal plug: nominal 115V or 230V at 50 - 60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiscent: 55W. Typical use: 130W. Max: 415W. Note: 0dBv = 775mV into open circuit. | Technical information
Size (WxHxD) 340mm x 265mm x 282mm (13.5" x 10.5" x 11.25") Weight 13 kgs (29 lbs) Drivers Bass: 2 x 130 mm (5 in) HF: soft dome 28mm (1.125in) Maximum SPL 108dB(C) Frequency Response 75Hz - 19kHz +/-2dB Input Connector XLR3 Female Impedance 10 kohm. Electronically balanced, RF filtered Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Sensitivity Rear switch to select: -14dBu to +4dBu in 2dB steps for 100dB SPL Max input for clip +16dBu at 5kHz on +4dBu setting Filters Subsonic -3dB at 27Hz, 12dB/oct (LF equaliser out). RF -3dB at 250Hz, 6dB/oct (HF equaliser out). Crossover 1.25kHz, 24dB/oct. User LF EQ 3 position rear switch to select: OFF for normal use (nominally flat), EXTENDED for nominal 1.5dB LF lift below 100Hz, and OUT for use with external sub woofer. User HF EQ 3 position rear switch to select: OFF for normal use (nominally flat), LIFT for +1.5dB from 8KHz, and CUT -1.5dB from 8KHz Power Amplifer LF output power >100W rms continuous.* HF output power >50W rms continuous.* * The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperature is > 30°C. T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz typ. 0.005% at 20W rms 1kHz. Hum + Noise >-100dB referred to clip Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (flashes red) indicates 0.5dB below signal clip. Thermal protection Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C. Power requirements Voltage Set by internal plug: nominal 115V or 230V at 50 - 60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiscent: 39W. Typical use: 85W. Max: 275W. Note: 0dBv = 775mV into open circuit. | Technical information
Size (WxHxD) 485mm x 612mm x 415mm (19" x 24.25" x 16.5") Weight 47 kgs (104 lbs) Drivers Bass: 2 x 200 mm (8 in) cone driver Mid: 1 x 75 mm (3 in) soft dome HF: 1 x 28mm (1.125in) soft dome tweeter Maximum SPL 112dB Frequency Response 40Hz - 18kHz +/-2dB Input Connector XLR3 Female Impedance 10 kohm. Electronically balanced, RF filtered Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Sensitivity Rear mounted 10 position rotary switch calibrated in 2dB steps. Maximum +4dBu for 100dB SPL at 1m: Max input level for clip >+16dBu at 5kHz Minimum -14dBu for 100 dB SPL at 1m: Max. input level for clip >-2dBu at 5kHz User LF EQ 3 position rear mounted switch to select: FLAT for normal use, CUT for nominal 2dB cut below 100Hz and LIFT for nominal 2dB LF lift below 80Hz User MF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift in the frequency band 500 - 3kHz User HF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift above 5kHz. Power Amplifer LF output power 230W rms continuous* Mid output power 110W rms continuous* HF output power: 100W rms continuous* T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz. typ 0.005% at 20W rms 1kHz Hum + Noise > -100dB referred to clip *Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperatures is <30°C Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (flashes red) indicates 0.5dB below signal clip. Thermal protection Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C Power requirements Voltage Set by internal plugs: nominal 115V or 230V at 50-60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiescent 105W, Typical use 280W, Max 950W |
