QUESTED VS3208 (Priced per Speaker)
Product Description
Technical information
Size (WxHxD) 485mm x 612mm x 415mm (19" x 24.25" x 16.5")
Weight 47 kgs (104 lbs) Drivers Bass: 2 x 200 mm (8 in) cone driver Mid: 1 x 75 mm (3 in) soft dome HF: 1 x 28mm (1.125in) soft dome tweeter Maximum SPL 112dB Frequency Response 40Hz - 18kHz +/-2dB Input Connector XLR3 Female Impedance 10 kohm. Electronically balanced, RF filtered Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Sensitivity Rear mounted 10 position rotary switch calibrated in 2dB steps. Maximum +4dBu for 100dB SPL at 1m: Max input level for clip >+16dBu at 5kHz Minimum -14dBu for 100 dB SPL at 1m: Max. input level for clip >-2dBu at 5kHz User LF EQ 3 position rear mounted switch to select: FLAT for normal use, CUT for nominal 2dB cut below 100Hz and LIFT for nominal 2dB LF lift below 80Hz User MF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift in the frequency band 500 - 3kHz User HF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift above 5kHz. Power Amplifer LF output power 230W rms continuous* Mid output power 110W rms continuous* HF output power: 100W rms continuous* T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz. typ 0.005% at 20W rms 1kHz Hum + Noise > -100dB referred to clip *Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperatures is <30°C Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (flashes red) indicates 0.5dB below signal clip. Thermal protection
Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C Power requirements Voltage Set by internal plugs: nominal 115V or 230V at 50-60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiescent 105W, Typical use 280W, Max 950W
Weight 47 kgs (104 lbs) Drivers Bass: 2 x 200 mm (8 in) cone driver Mid: 1 x 75 mm (3 in) soft dome HF: 1 x 28mm (1.125in) soft dome tweeter Maximum SPL 112dB Frequency Response 40Hz - 18kHz +/-2dB Input Connector XLR3 Female Impedance 10 kohm. Electronically balanced, RF filtered Wiring Pin 1 Ground, Pin 2 Hot, Pin 3 Cold Sensitivity Rear mounted 10 position rotary switch calibrated in 2dB steps. Maximum +4dBu for 100dB SPL at 1m: Max input level for clip >+16dBu at 5kHz Minimum -14dBu for 100 dB SPL at 1m: Max. input level for clip >-2dBu at 5kHz User LF EQ 3 position rear mounted switch to select: FLAT for normal use, CUT for nominal 2dB cut below 100Hz and LIFT for nominal 2dB LF lift below 80Hz User MF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift in the frequency band 500 - 3kHz User HF EQ 3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift above 5kHz. Power Amplifer LF output power 230W rms continuous* Mid output power 110W rms continuous* HF output power: 100W rms continuous* T.H.D. <0.03% at levels up to 1dB below clip, 20Hz - 20kHz. typ 0.005% at 20W rms 1kHz Hum + Noise > -100dB referred to clip *Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperatures is <30°C Indication Power on Front mounted LED (green) indicates power applied Overload Front mounted LED (flashes red) indicates 0.5dB below signal clip. Thermal protection
Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C Power requirements Voltage Set by internal plugs: nominal 115V or 230V at 50-60Hz AC. 230V setting: Min 160V (restricted output power): Max 263V 115V setting: Min 80V (restricted output power): Max 132V Consumption Quiescent 105W, Typical use 280W, Max 950W
